Thats awsome! Tis will come in handy alot for me! I want to rewire the craftsman, but keep the key switch. This will save me some guess work! Show Like dangeroustoys56Veteran Member  1000+ Posts Age : 52 Join date : 2010-02-10 Posts : 1726 Location : Florida, USA I had a different diagram one for the twin wire off the stator - but the wires wouldnt match the ign switch . These are also the clearest/sharpest copies i could find as well ( plus color coded). Like ChunkEstablished Member 500+ Posts Age : 31 Join date : 2010-02-10 Posts : 779 Location : Angus, Scotland Yeah, thanks for uploading these dangeroustoys. These are really gonna be useful. Like ChunkEstablished Member 500+ Posts Age : 31 Join date : 2010-02-10 Posts : 779 Location : Angus, Scotland Most lawn tractors have an chraging circuit under the coil, with two wires coming from them. These can go bad though, best way is to check it with a voltmeter, you should be producing about 12-14v at full rpm, and about 6v or so at idle. Like dangeroustoys56Veteran Member 1000+ Posts Age : 52 Join date : 2010-02-10 Posts : 1726 Location : Florida, USA Yepper- older motors that use a generator dont have the stator , push mowers w/o electric start dont, ive got a 70 toro with a 5HP electric/ pull start motor that doesnt have a stator - it originally had a lil plug in the side where youd plug it in the wall to charge the battery ( that part is gone now). Like ChunkEstablished Member 500+ Posts Age : 31 Join date : 2010-02-10 Posts : 779 Location : Angus, Scotland I beleieve the red goes to the +ve of the battery, as this is what charges it, and the black is to run lights etc from. Dont quote me on this, dangeroustoys will have a better idea. Like arild365Frequent Poster Age : 27 Join date : 2010-02-11 Posts : 320 Location : Canada, BC my craftsman doesnnt and never has had a fuse!! does it matter? never had any problem! :S Like arild365Frequent Poster Age : 27 Join date : 2010-02-11 Posts : 320 Location : Canada, BC oh and I HATE WIRING!! for me its just too complicated like i understand it all but i can do the lighting and stuff but man urrghhh i get so frustrated Like RompinRedneckNew Member Age : 29 Join date : 2012-01-01 Posts : 41 Location : CT Sorry for bringing this thread back from the dead, but I am having a problem directly related to this thread. What do I do with the black wire if my tractor does not have lights? Like fergNew Member Join date : 2011-10-24 Posts : 45 Location : Cheshire, England RompinRedneck wrote:Sorry for bringing this thread back from the dead, but I am having a problem directly related to this thread. What do I do with the black wire if my tractor does not have lights? Like RompinRedneckNew Member Age : 29 Join date : 2012-01-01 Posts : 41 Location : CT What if I have no headlamps? Wouldn't that not complete the circuit? Like New Member Age : 28 Join date : 2010-10-03 Posts : 170 Location : Ontario Canada ok so what if i have the carb with a wire coming out of it? i need to put that engine in another tractor and i cant take the wire harness with it because the safety switches wont work on the new tractor Like RompinRedneckNew Member Age : 29 Join date : 2012-01-01 Posts : 41 Location : CT Jordan wrote:ok so what if i have the carb with a wire coming out of it? i need to put that engine in another tractor and i cant take the wire harness with it because the safety switches wont work on the new tractor Like JordanNew Member Age : 28 Join date : 2010-10-03 Posts : 170 Location : Ontario Canada have you tested this out yet? because its actually my brother engine that has it and i dont wanna have to pay to fix it for him if i do something wrong, and he actually runs the manual shut off anyway because if the fuel is left on it floods the engine Like JamusEstablished Member 500+ Posts Age : 43 Join date : 2010-06-28 Posts : 511 Location : Southern WV I have an engine with that electric valve on it in my murray. I ran it to a toggle switch as a sort of secondary cutoff along with the coil wire. I can't remember how I wired it in though. Like JordanNew Member Age : 28 Join date : 2010-10-03 Posts : 170 Location : Ontario Canada i have a spare carb for the engine anyway so i just cut the plunger off and the engine runs fine, no problems at all so i put the engine on the other tractor and wired it like i normally do and it runs great Like csonka39New Member Join date : 2012-01-06 Posts : 1 First of all, Thanks for response. Correction, I have a 16 hp twin briggs pig, ordered a new coil as the one the motor had was burnt at the ground and wires where coming from inside the plastic. So, technically once i install and gap the new coil w/ the ground unattached the motor should give me some spark, correct?, from there I can bypass wiring like the diagram from fearlessfront, and be set to dominate the back 1/2 acre. Like richie thomasVeteran Member 1000+ Posts 2014 Build-Off Entrant Age : 27 Join date : 2011-08-04 Posts : 1434 Location : east dublin georgia anyone have a good diagram for wiring an opposed twin? Like JamusEstablished Member 500+ Posts Age : 43 Join date : 2010-06-28 Posts : 511 Location : Southern WV I've had good luck wiring up a couple of my mowers, including a twin, using the diagram posted by fearlessfront. It's in the wiring topic stickied to the top. What is the red wire on a Briggs & Stratton engine?RED WIRE - This is your DC cable, it should be connected directly to positive power on your battery. This wire charges your battery. BLACK WIRE - This is the engine kill switch, It needs to run to an ON/OFF switch and then run to earth. DO NOT CONNECT THIS WIRE TO POSITIVE POWER!
Why won't My Briggs and Stratton lawn mower keep running?Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas. If this doesn't work, you might need a new fuel filter.
How do you wire an ignition on a riding lawn mower?How to wire a lawnmower ignition switch, step by step. Step 1: Obtain a circuit diagram.. Step 2: Locate all components that need wiring.. Step 3: Connect the switch to ground.. Step 4: Connect the switch to the Solenoid.. Step 5: Wire the magneto to the switch.. Step 6: Provide voltage by connecting the battery.. |
Briggs and stratton 18 hp twin wiring diagram
Related Posts
Copyright © 2024 chuyencu Inc.
