How to program remote to chamberlain garage door opener

How do I add or reprogram a hand-held garage door remote control?

Press and release the LEARN button on the garage door opener unit. The learn indicator light will glow steadily for 30 seconds. Within this 30 second time period, press and hold the button on the hand-held remote. Next, release the button when the overhead opener unit’s lights blink. If light bulbs are not installed on your opener, then two clicks will be heard.

To erase all codes from motor unit memory:
Press and hold the LEARN button on motor unit until the learn indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use. Press and hold the ENTER button. Next, release the button when the overhead opener unit’s lights blink. If light bulbs are not installed on your opener, then two clicks will be heard.

How do I program my vehicle’s HomeLink® system with my Door opener?

Please follow the following steps:
Press and hold the two outside HomeLink buttons—releasing only when the indicator light begins to flash rapidly (after 20 seconds). Some vehicles may require the ignition to be in the “ON” position during the entire programming process.

Hold the end of the hand-held remote control (transmitter) you wish to train approximately 1-3 inches from the HomeLink surface—keeping the indicator light in view.

Simultaneously press and hold both the hand-held transmitter button and the designated HomeLink button—releasing both buttons only when the indicator light changes from a slow to a rapid blink.

Press the “SMART BUTTON” or “LEARN BUTTON” on the Raynor opener for one second and release. (Note: you only have 30 seconds in which to initiate step 5.)

Return to the vehicle and firmly press the programmed HomeLink button TWO times (press and hold each time for two seconds). The garage door opener should have activated upon the second press of the HomeLink button.

Note: HomeLink equipped vehicle models manufactured in 1995, 1996, and early 1997 will not be compatible. To determine if a 1997 HomeLink equipped vehicle is Security + compatible, follow steps 1-3 above. Upon the completion of steps 1-3, press and hold the programmed HomeLink. If the LED blinks rapidly for two seconds and then turns solid, the HomeLink is rolling code compatible and the remaining programming steps can be completed. If the LED is solid when the programmed button is pressed, then the HomeLink is not compatible.

Home » DIY » Remotes » How to program a Chamberlain Clicker Universal Remote Control / LiftMaster 375?

The Chamberlain Clicker Universal Remote Control (KLIK1U, KLIK3U, KLIK3U-BL, KLIK3U-PK) 

aka LiftMaster 375UT (375 LM)  is a universal remote that 

will program to most garage door openers and external receivers using learn buttons or DIP switches.

The first step is determining if your garage door opener or external receiver uses a learn button or DIP 

switches.

Newer garage door openers utilize a learn button

and older units utilize DIP switches.

Programming the clicker universal remote to a garage door opener/receiver with learn button:

1. Start with the garage door closed.

2. Open the remote  by sliding the battery cover open. Inside the remote you will see a

program button on one side and DIP switches on the other side. Press and hold the program

button for about 2 seconds, until the LED light illuminates.

3. Press the learn button on the garage door opener or external receiver. The learn button will be

on the back or side of the garage door opener motor. You will have to use a ladder to locate and

access the learn button. Always use caution any time you use a ladder to prevent accidental

falls.

4. Press and release the button on the remote you want to operate the garage door opener. Wait

until the LED on the remote stops flashing between button pushes. Continue to press the

button until you hear a click from the garage door opener, the light on the garage door opener

flashes or the garage door starts to open.

5. Press and release the program button to exit the programming mode.

6. Press the button you just programmed to verify the garage door opener remote is programmed

and the garage door opens and closes using the remote. If the garage door does not open and

close, repeat the programming steps.

These same steps work for programming to an external receiver or a gate opener with a learn button.

Number of button pushes required for the following Openers to program the universal clicker:

(Number of times press and release require / Learn button and Years

Brand / Models)

Master Mechanic                                                                                                            642-2MM

Access Master M385,

ChainMax 1000, ChainMax 1200, ChainMax 1200 4042, SilentMax 750, SilentMax 1000,  SILENTMAX 1000 3042, SILENTMAX 1200, SILENTMAX 1200 4042, TriloG 1200, TriloG 1500, TriloG 1500 4064, TriloG 1500 4064H, PowerLift 900, PowerMax 1200, PowerMax 1500, IntelliG 1000, IntelliG 1000 3024, IntelliG 1000 3024H, IntelliG 1200, IntelliG 1200 4024, IntelliG 1200 4024H, CB 1000, CB 1200, 1022, 1024, 1028, 1035, 1042, 2020, 2022, 2024, 2028, 2035, 2036, 2040, 2040L, 2042, 2055, 3035, 3055, 3064, 7035, 7055, BeltLift 600, Directlift 2060, Directlift 3060, GPower 900, Machforce 4062, Excelerator 4062, SilentMax Connect, SteakthDrive 750, StealthDrive 750 Plus,

H8000, 4560, 500ML, 700ML, Excelerator, GCG350,

350L, 350L-1x, 350L-2, 350L-2C, 350L-2WK, 350L-2WKC, Chain Glide, H2000, 

OverHead Legacy

         Do-It, Master Mechanic, True Value

Access Mater –  M885, M8856 

Craftsman  -CMXEOCG471,CMXEOCG981, CMXEOCG231,CMXEOCG571, CMXEOCG771, CMXEOCG781

 3014, 3018, 3018DLX, 3514, 3314, 3414, 3220C, 3222C, 3224C, 3320B, 3322B, 3322B, 3324B, 3212, 3213, 3312, 3313, 3412, 3012, 3016, 3512

Remember the LED light on the clicker must stop flashing between each press of the button during

programming.

If your garage door opener or receiver utilizes DIP switches you must match the DIP switches on the

remote to the DIP switches on the garage door opener or receiver. It could be 8-12 DIP switches with 2

or 3 positions per switch. The DIP switches much match identically. If your garage door opener or

receiver has only 2 positions and programming does not work, switch the off and on positions on the

remote as they may be reversed.

Program chamberlain garage door opener and clickers, in general, is a fairly simple process if you follow the listed procedures. You can

contact a local garage door service company to provide the remote and program the remote for you.

Labor rates will vary depending on your area but is normally around $70 – $120 (Include full garage door 

and opener inspection) and the cost of the  universal clicker remote is around $35 – $50.

Need garage door repair in Dallas tx? call us today

Fill Out The Form

Recent Post

Which button is the Learn button on Chamberlain?