Below are six reasons why a Maytag Centennial washer won’t spin: If you overload the clothes in your Centennial washer, the laundry machine may fail to spin. The load will become too bulky to turn within the drum, and even if it turns, you’ll likely have wet clothes at the end of the spin. That explains why Maytag recommends a ¾ loading. That leaves enough room for the clothes to spin. Note that while you may not have overloaded the clothes, they may fail to turn if they are not uniform in the washer. So, this is another thing to watch out for when loading your Centennial
washer. Fix Reduce the clothes load if they are jammed/overloaded. Remember to keep the load ¾ full. So, you may have to take out some of the clothes. Meanwhile, spread them evenly in the washer to ensure they can spin smoothly. 2. Machine ImbalanceYour Centennial washer could also fail to spin because it’s out of balance. That could be because its feet are loose or it’s resting on an uneven surface. So, you’ve to figure out which of the two is stopping your washer from turning, especially when it vibrates when you turn it on. Note that often, the reason why you have uneven laundry is that of an imbalance washer. So, you could fix two issues here. Fix Adjust the washer’s feet if they are loose and ensure they are uniform. Then ensure the washer is resting on stable/uniform ground. If it’s not, move it. But before you can run the washer, check the clothes to ensure they are even. If not, redistribute them uniformly. 3. Wrong Setting for Bulky ClothesAn incorrect setting could explain why your washer won’t spin bulky clothes. For example, if you’ve selected a Low-Spin cycle, the washer will spin at an almost unnoticeable pace. And if the No-Spin cycle is on, the washer won’t spin at all. Also, if you use a Delicate, Hand Washing, or Gentle setting on bulk clothes, the clothes won’t spin. So, you must choose the right setting for your washer, depending on the clothes you wash. Fix Confirm that you are using the right setting. If a No-Spin or Low-Spin cycle is on, consider opting for a high-speed setting for your bulky load. Only use such settings on less bulky clothes and when you need more soaking than spinning. 4. Clogged DrainYour Centennial washer may not spin because of poor drainage. If the drain hoses are clogged, water will stagnate in the washer tube. That means that even if the washer spins, which is less likely, you’ll have wet clothes at the end of the cycle. So, inspect the drain hose to ensure the water drains smoothly. Fix Detach the drain pipe to inspect it for clogging. If the drain pipe is dirt clogged, run hot water to unclog it. 5. Obstructed DrumThe washer might not be spinning because of something in the drum obstructing it. Start by looking for debris in the drum, which could deter the washer from turning. If there’s no debris, then the obstruction could be trapped clothes. It could also be a combination of the two. Fix Inspect the washer’s drum for debris and clothes obstructions and remove them before running the washer. 6. Component failureLastly, if the reason why your Centennial washer won’t spin is none of the above 6, then it could be a failed component. One of these components could be worn out, damaged, or dysfunctional, thus preventing the washer from spinning.
Fix Carefully examine all the above components for fault and replace the worn-out or malfunctioning ones. Talk to a laundry machine expert if you cannot do the component replacement DIY. Other Maytag Centennial Spinning IssuesMaytag Centennial Washer Stopped Spinning Mid-CycleIssues like power failure, an error code, or a wrong cycle selection could stop the centennial washer from spinning mid-cycle. Regarding an incorrect cycle selection, the washer will stop spinning if you select a low-spin or no-spin cycle mid-cycle. And when it comes to power failure, the washer will stop spinning mid-cycle due to a tripped breaker or exploded fuse. You also have to watch out for a power outage. And if there is an error code, clear it first by resetting the washer (steps shared below). Maytag Centennial Washer Not Spinning Clothes DryIf your Maytag Centennial washer won’t spin clothes dry, it’s likely because of a wrong setting, especially a no-spin or low spin. It could also be that the load is excess and out of balance. If so, you need to reduce the load size and balance it. It may help to select a high-spin to remove the excess water properly. The washer could also fail to spin dry clothes because it’s unstable or due to a clogged drain. Also, consider the possibility of a power failure, a faulty lid switch, or excessive suds. Maytag Centennial Washer Not Spinning or DrainingYour Maytag Centennial is neither spinning nor draining because of an excess load, a clogged drain, or excessive suds. So, check the laundry load to ensure the clothes are not jamming. Then check the drain pipe for clogging and unblock it and avoid using too much detergent if there are excessive suds. Also, consider the possibility of a bad lid switch preventing the lid from closing. Other possible explanations include a worn-out clutch or transmission, which won’t allow the washer to spin. How to Put a Maytag Centennial Washer in Diagnostic Mode?Suppose you cannot find why your Centennial washer won’t spin. If so, putting your Centennial washer in diagnostic mode is advisable. That will allow you to discover hidden error codes that could point you to the reset problem. Here’s how to do it:
How to Reset a Maytag Centennial Washer?You can fix some issues and clear error codes by resetting your washer. Here’s how to reset a Centennial washing machine:
People Also Ask1. What Do You Do When a Maytag Washing Machine Won’t Spin?Consider checking the laundry load, settings, and washer leveling when your Maytag washer won’t spin. If the laundry is overloaded, reduce it to ¾ full; if it’s uneven, spread it evenly. In the meantime, ensure you are using the right setting and that the laundry is not out of balance. 2. How Can I Reset a Maytag Washer Not Spinning?You can reset your non-spinning washer by unplugging it for about 20 seconds. If the washer doesn’t restart, unplug it for 10 minutes or even up to 30 minutes. Meanwhile, try to determine if something prevents the washer from spinning. Closing RemarksNow you know how to fix a Maytag centennial washer not spinning. You should consider several issues when your washer won’t spin at all, stop spinning mid-cycle, or fail to spin dry. That includes jammed or uneven laundry, imbalance washer, wrong setting, drain clogging, drum obstruction, or component malfunction. And as shared, the components to pay attention to include the lid switch, motor coupling, drive belt, clutch, shift actuator, and transmission. Why does my Maytag washer not spin all the water out?Your washer will not be able to adequately pump the water out of the appliance if the drainpipe (standpipe) exceeds 96" (244 cm). In this case, the water may flow back into the washer. Make sure the drain hose is not kinked or clogged. Straighten the hose for adequate water flow.
Why is my washer not spinning all the water out of my clothes?Typically, this means checking the drain hose, drain pump, and any filters or coin traps that could be blocked. Other causes of clothes still being wet after the spin cycle include an unbalanced washer, using the wrong detergent, or a worn or loose drive belt.
What would cause a Maytag Centennial washer not to spin?Check the Drive Pulley
The next possible cause of your Maytag washer not spinning is a worn-out or faulty drive pulley. The pulley works with the drive belt to make the washer rotate during a wash cycle.
|